四虎网站在线观看,亚洲人久久久综合网站,欧美狠狠鲁,黄色网络久久2

服務熱線: 400-117-8816
           13406879330

扭剪扳手,扭剪螺栓專用扳手,扭剪電動扳手,扭剪槍生產廠家

當前位置:首頁>新聞中心如何安裝扭剪型高強螺栓?

如何安裝扭剪型高強螺栓?

來源:http://www.8ying.cn日期:2021-10-11 發布人:admin

扭剪型高強螺栓的連接副形式在《GB/T3632-2008》中有規定:連接副包括:一個螺桿/一個螺母/一個墊圈。

The form of connection pair of torsional shear high-strength bolt is specified in GB / t3632-2008: the connection pair includes: a screw / a nut / a washer.
扭剪型高強螺栓安裝規定:
Installation regulations for torsional shear high strength bolts:
1安裝時高強螺栓應自由穿入孔內,不得強行敲打。扭剪型高強螺栓的墊圈安在螺母一側,墊圈孔有倒角的一側應和螺母接觸,不得裝反(大六角頭、高強螺栓的墊圈應安裝在螺栓頭一側和螺母一側,墊圈孔有倒角一側應和螺栓頭接觸,不得裝反)。
1. During installation, the high-strength bolt shall freely penetrate into the hole and shall not be knocked by force. The washer of torsion shear high-strength bolt shall be installed on the nut side, and the side with chamfer in the washer hole shall contact the nut and shall not be installed reversely (the washer of large hexagon head and high-strength bolt shall be installed on the bolt head side and nut side, and the side with chamfer in the washer hole shall contact the bolt head and shall not be installed reversely).
2螺栓不能自由穿入時,不得用氣割擴孔,要用絞刀絞孔,修孔時需使板層緊貼,以防鐵屑進入板縫,絞孔后要用砂輪機孔邊毛刺,并鐵屑。
2. When the bolt cannot penetrate freely, it is not allowed to ream the hole with gas cutting. The hole shall be reamed with a reamer. When repairing the hole, the plate layer shall be close to prevent iron filings from entering the plate joint. After reaming, the burr at the hole edge shall be removed with a grinder and the iron filings shall be removed.
3螺栓穿入方向宜一致,穿入高強螺栓用扳手緊固后,再卸下臨時螺栓,以高強螺栓替換。不得在雨天安裝高強螺栓,且摩擦面應處于干燥狀態。
3 bolts should be threaded in the same direction. After threading high-strength bolts and tightening them with a wrench, remove the temporary bolts and replace them with high-strength bolts. High strength bolts shall not be installed in rainy days, and the friction surface shall be dry.
4.高強螺栓的緊固:必須分兩次進行,一次為初擰。初擰緊固到螺栓標準軸力(即設計預拉力)的60%~80%,初擰的扭矩值不得小于終擰扭矩值的30%。二次緊固為終擰,終擰時扭剪型高強螺栓應將梅花卡頭擰掉。為使螺栓群中所有螺栓均勻受力,初擰、終擰都應按一定順序進行。一般接頭:應從螺栓群中間順序向外側進行緊固。從接頭剛度大的地方向不受約束的自由端進行。從螺栓群向四周擴散的方式進行。
4. Fastening of high-strength bolts: it must be carried out in two times, one for initial tightening. The initial tightening shall be tightened to 60% ~ 80% of the standard axial force (i.e. design pretension) of the bolt, and the torque value of the initial tightening shall not be less than 30% of the final tightening torque value. The secondary tightening is the final tightening. During the final tightening, the plum blossom bayonet shall be screwed off by the torsion shear high-strength bolt. In order to make all bolts in the bolt group bear stress evenly, the initial tightening and final tightening shall be carried out in a certain order. General joints: fasten from the middle of the bolt group to the outside. From the place with large joint stiffness to the unrestrained free end. Spread from the center of the bolt group to all around.

少妇人妻 一区二区| 欧美亚洲视频图片小说 | 亚洲图片国产欧洲| 亚洲日韩在线第一页| 亚洲激情三区四区| 92精品福利视频| 图片 自拍 另类欧美| 91AV美女| 日本xxxx一区二区| 欧美人妻日韩偷窥| 天天干天天日天天插天天射天天干 | 午夜精品三| 日本中文一区二区三区免费在线观看| 人妻午夜电影| 午夜视频福利在线| 黄色乱轮电影在线观看| 蜜臀av一区二区三区多| 中美日韩在线观看成人| 日韩一本一区| 色色成人欧美| 国产暴力强伦轩1区二区电影| 婷婷精品国产一区二区三区日韩| 国产人妻无码| 欧美在线亚洲图区| 夜间导航福利视频一区二区| 国产麻豆出轨视频| 国产曰产精品久久| 久久久999在线视频| 美女的鸡巴的免费视频| 在线观看亚洲欧美不卡视频| 久久黄色97| 天天操夜夜草一区| 亚洲一区影院| 91tv亚洲精品香蕉国产一区| 一至六区麻豆| 亚洲欧洲国产日韩另类| 最近中文字幕在线| 日本欧美蜜臀久久99精品久久 | 国产精品国产三级国产普通话对白| 日日干日日操日日日| 日本一区二区精品在线|